Follow Haybuster
H-1000 Series II - Tub Grinder - Overview
H-1000 Series II General Specifications
 |
||
| WEIGHT | ||
| Total | 6,830 lbs. (3,098 kg) | |
| TRANSPORT DIMENSIONS | ||
| Width | 10 ft. 3 in. (3.12 m) | |
| Height | 10 ft. 2 in. (3.10 m) | |
| Length | 20 ft. (6.10 m) | |
| CHASSIS FEATURES | ||
| Towing Arrangement | Clevis hitch | |
| Bearings | Tapered roller | |
| TUB FEATURES | ||
| Loading Height | 8 ft. (2.44 m) | |
| Tub Width at Flare | 10 ft. (3.05 m) | |
| Depth | 44-1/2 in. (1.13 m) | |
| Tub Inside dia at Base | 8 ft. (2.44 m) | |
| Tub Wall Thickness | 12 gage (2.66 mm) | |
| Tub Floor Thickness | 10 gage (3.42 mm) | |
| Drive Mechanism | Full Sprocket around tub Electro/Hydraulic | |
| Speed Control | Electronic Governor | |
| HAMMERMILL | ||
| Length | 44-1/2 in. (1.13 m) | |
| Diameter, Hammers Extended | 26 in. (66 cm) | |
| Feed Opening | 27 in. x 45 in. (68.58 cm x 114.3 cm) | |
| Hammers | 3/8 in. (9.53 mm) Thick, A.B. Hardened Swing | |
| Number of Hammers | 64 | |
| Hammer Rods | 15/16 in. (23.81 mm) dia., Case Hardened | |
| Cylinder Plates | 3/16 in. thick x 15-¾ in. dia. | |
| Cylinder Shaft | 3 in. (7.62 cm), Stress Proof Steel | |
| Drive End Bearing | 2-3/4 in.(6.99 cm), Pillow Block | |
| Idle End Bearing | 2-7/16 in. (6.19 cm), Pillow Block | |
| Screens | 1/8 in. (3.18 mm), 3/16 in. (4.76 mm), or 1/4 in. (6.35 mm) thick and various hole sizes from 1/8 in. (3.18 mm) to 4 in. (101.6 cm) | |
| Screen Area | 2,400 sq. in. (15,483 sq. cm) | Drive | PTO through multiple V Belts |
| BELLY CONVEYOR | ||
| Type | Double Free Floating Augers | |
| Auger Size | 9 in. (22.86 cm) x 96 in. (2.44 m) | |
| Width | 33-¾ in. (85.73 cm) | |
| Drive | Mechanical | |
| DISCHARGE CONVEYOR | ||
| Type | Rubber Belt with Cleats | |
| Drive | Mechanical | |
| Drive & Idler Roller Type | “Easy Clean” | |
| Length | 20 ft. (6.1 m) | |
| Width | 18 in. (45.72 cm) | |
| Maximum Conveyor Lift Height | 13 ft. 9 in. (4.19 m) | |
| Conveyor Lift | Hydraulic | |
| Conveyor Lift Cylinder | 3" x 12" (7.62 cm x 30.48 cm) | |
| Conveyor Fold | Hydraulic Folding Over Rear of Tub | |
| OPERATOR CONTROLS | ||
| Tub Rotation | 3 Position Hydraulic Valve for Clockwise, Stop, & Counter-Clockwise | |
| Tub Speed | DuraTech Model RCB93 Electronic Governor Stabilizes Engine Load by Controlling Tub Rotation Speed | |
| Conveyor Lift | 3-Position Hydraulic Valve for Raise, Hold, & Lower | |
| REQUIREMENTS FOR OPERATION TRACTOR | ||
| PTO Horsepower Required | 80 HP (59.7 kw) to 175 HP (130.5 kw) | |
| Min. Tractor Hydraulic Output | 8 gpm at 1500 psi (30.3 lpm x 10,345 kPa) | |
| Hydraulic Remote Controls | (1) Double-acting control valve with quick coupler outlets | |
| Electrical | 12 VDC | |
| GRINDER | ||
| Hydraulic Reservoir | 12 gallon (45.4 liter) capacity | |
| Oil Requirement | Mobil 423, Co-op Super HTB or Equivalent | |
| SMV Sign | Standard equipment | |
| Road Lights | Standard equipment | |
H-1000 Series II Options
| PTO Shaft -1000 RPM | ||
| Tractor Half, 1-3/4 in, 20 Spline Shaft | ||
| Tractor Half, 1-3/8 in, 21 Spline Shaft | ||
| Hammermill Feeding | ||
| Slug Buster, 5 tooth screen hold down | ||
| Mill Grate, for grinding tough hay or crop residues | ||
| Geyser Plates | ||
| Geyser Plate Kit, use with the Slug Buster | ||
| Geyser Plate Kit, slotted, use with the Mill Grate | ||
| Tires | ||
| (Set of 2) 9.5 x 14 - 8 ply Implement Tires | ||
| (Set of 2) 31x10.5x15 - load rating "C" Highway Rated Tires | ||
| Loose Hay Guide, Front | ||
| Hopper for Grain Grinding | ||
| Ear Corn Kit | ||
| Better diets for dairy cows - an article from the USDA - describes how finely ground grains/corn can offer a better diet for cows. | ||
| Closed Center Conversion Kit | ||
| This kit is required to operate the conveyor lift valve properly, with John Deere 60 and older series tractors. | ||
| Grinding Screens | ||
| 1/8 in. (3.18 mm) Round Hole Screen Half* | ||
| 3/16 in. (4.76 mm) Round Hole Screen Half** | ||
| 1/4 in. (6.35 mm) Round Hole Screen Half | ||
| 3/8 in. (9.52 mm) Round Hole Screen Half | ||
| 1/2 in. (12.7 mm) Round Hole Screen Half | ||
| 5/8 in. (15.88 mm) Round Hole Screen Half | ||
| 3/4 in. (19.05 mm) Round Hole Screen Half | ||
| 1 in. (25.4 mm) Round Hole Screen Half | ||
| 1-1/2 in. (38.1 mm) Round Hole Screen Half | ||
| 2 in. (50.8 mm) Round Hole Screen Half | ||
| 3 in. (7.62 cm) Round Hole, Screen Half (standard) | ||
| 4 in. (10.16 cm) Round Hole, Screen Half (standard) | ||
| Dummy (Open) Screen Half | ||
| *1/8 in. (3.18 mm) thick, **3/16 in. (4.76 mm) thick, all other screens are 1/4 in. (6.35 mm) thick |
||
Sorry, there are currently no videos for this product.
